Commercial 2411
Non Insulated Ribbed Panel
Model C2411 has a smooth finish and is roll formed with two major ribs and six minor ribs.
SECTIONS
Sections are 2” thick. Sections are roll formed from 24 gauge hot dipped galvanized steel.
Section joints are tongue and groove.
Exterior and interior are pre-finished using a urethane primer and polyester finish.
Bottom sections have a flexible vinyl bottom astragal.
All doors are built to meet or exceed standards established by ANSI/DASMA 102-2011. Wind load rated doors are available. Please consult Garage Door Distributors.
Manual operation is standard for all doors.
End stiles and center stiles are ‘C’‑shaped made from 18 gauge galvanized steel.Available section heights are 21” and 24”.
HARDWARE
Steel track and hardware components are galvanized to prevent rust and/or corrosion.
Vertical tracks are a minimum of 16 gauge steel.
Vertical track is graduated at 1/8” per linear foot of door height.
2” bracket mounted track is standard.
2” and 3” clip style angle mounted track is available for all sizes where not standard. Consult Garage Door Distributors for occurrence of 3” track.
2” and 3” full continuous taper angle mounted track is available on door heights to 16’-0”.
Horizontal tracks are a minimum 16 gauge steel with 14 gauge steel support angles as required.
12” radius is also available on 2” track on doors up to 14’-0” tall at no additional cost.
Double end hinges are furnished on doors 18’-0” and wider.
All hinges are 14 gauge minimum.
10-ball rollers are standard on all size doors.
Cable drums are die cast aluminum with aircraft type cable.
Springs are oil tempered, helical, torsion type mounted to a steel cross header shaft.
Inside lock is standard. Cylinder lock is optional.
Warranty
C2010, C2400 & C2500 Series Steel Commercial Garage Doors
1 Year Warranty
Haas Door Company warrants its commercial models C2010, C2400 & C2500 series steel garage door sections to be free from defects in workmanship and material for a period of one (1) year from date of installation. This Warranty applies only to steel garage door sections manufactured by Haas Door Company and components manufactured or supplied by Haas Door Company.
The warranty excludes: (1) Sections and/or component parts which have been damaged due to misuse; (2) Sections and/or components which have been improperly installed, maintained or operated; (3) Sections and/or components that have been damaged due to accident; (4) Sections and/or components that have been damaged due to exposure to corrosive fumes/chemicals, alkaline cleaning agents, condensation or fire; (5) Performance of and/or any damage or defect caused by coatings applied subsequent to the original factory-applied finish.; (6) Repair and/or replacement labor charges, including travel cost; (7) Damages resulting from other causes beyond the manufacturers control.
In the event any defect is claimed during the warranty periods, a claim in writing must be submitted to Garage Door Distributors. This claim must be submitted within fifteen (15) days of the discovery of the suspected defect. The door and all components must be available for inspection by an authorized Garage Door Distributors representative. Upon verification of a manufacturing defect, Haas Door Company will provide repair or replacement part(s) at its option.
THE MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF ANY BREACH OF THIS EXPRESS LIMITED WARRANTY, including but not limited to any damage to buildings, other property or for any injuries or damages sustained by any person whomsoever, or the recovery of any direct or indirect costs such as shipping, travel, lost time, installation labor charges, paint or painting, cleaning, repair, or other building materials.
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THE PURCHASE; THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDIES WHICH BUT FOR THE WARRANTY CONTAINED HEREIN MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE.
----- T H I S W A R R A N T Y I S N O T T R A N S F E R A B L E -----
Panel Construction
- 2” Thick Ribbed Sections
- 24-Gauge Steel Options
- 15" Radius Horizontal Track
- Vertical Track with Jamb Brackets
- 2" White Nylon, 11 Ball Bearing Rollers
- Non-insulated
- Tongue-and-Groove Construction
- 4 Color Options